Description: Data Sheet Overview Audio input (A/D), output (D/A) expander for Symetrix systems that capitalizes on the surplus DSP of a Dante-enabled Symetrix DSP unit to bring overall system costs down.4 mic/line inputs, including +48 VDC phantom power, and 4 line outputs with the industry leading performance specifications of Radius, Edge, and Prism DSPs.Configured with Symetrix Composer. No third-party software, archaic DIP switches, or complicated front panel menus.Network audio expansion using Dante protocol over standard IT networks. Ultra-low latency.PoE Injector included.Optional 1U rack tray and 1/2U surface mount bracket available for separate purchase.The cost effective xIO 4×4 increases a system’s analog input and output channel capacity resulting in a reduction in overall price per channel. Designed exclusively for use with Dante-enabled Symetrix DSP units, each of the four analog inputs’ parameters (5 gain levels, phantom power) and four analog outputs’ parameters (mute), along with bus assignments, are configured using Symetrix Composer open architecture software. xIO 4×4 set up is logical and fast with no requirement to use third-party software; there are no mechanical switches or circuit board jumpers to set. Systems are simpler, cost less, and have fewer potential points of failure. A half-rack form factor conserves rack space. Optional 1U rack tray and 1/2U surface mount bracket are available for separate purchase.Device Specifications ANALOG INPUTSFrequency Response20 Hz – 20 kHz, ± 0.5 dB.Channel Separation> 111 dB 1 kHz, +24 dBu.Connectors3.5 mm Phoenix® connectors.Number of InputsFour (4) switchable balanced mic or line level.Nominal Input Level+4 dBu with 20 dB of headroom.Maximum Input Level+23 dBu.Mic pre-amp gain0, 11.8, 24, 44 or 54 dB switchable.Mic pre-amp EIN< -127dB with 150 ohm source impedance.CMRR> 76 dB 1 kHz, unity gain.Input impedance8k Ohms balanced, 4k Ohms unbalanced.Phantom power (per input)+48 VDC 10 mA maximum.Dynamic range> 116 dB, A-weighted.THD + Noise< -100 dB, unweighted; 1 kHz +22 dBu with 0 dB gain.Latency0.28 mS.ANALOG OUTPUTFrequency Response20 Hz – 20 kHz, ± 0.5 dB.Channel Separation> 111 dB 1 kHz, +24 dBu.Connectors3.5 mm Phoenix® connectors.Number of outputsFour (4) balanced line level.Nominal output level+4 dBu with 20 dB of headroom.Maximum output level+24 dBu (+22.8 dBu into a 2k Ohm minimum load).Output impedance300 Ohms balanced, 150 Ohms unbalanced.Dynamic range> 118 dB, A-weighted.THD + Noise< -105 dB, unweighted; 1 kHz +22 dBu with 0 dB gain.Latency0.60 mS.SYSTEMSampling Rate48 kHz, ± 100 ppm.Dante CableStandard CAT6, maximum device-to-device length = 100 meters.MECHANICAL SPECIFICATIONSSpace RequiredHalf rack unit (WDH: 20.83 cm x 22.86 cm x 4.37 cm / 8.2 in. x 9 in. x 1.72 in.) Depth does not include connector allowance. Allow at least 3 inches additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.ElectricalPoE IEEE 802.3af Class 0, 10 Watts maximum. No line voltage switching required (100-250 VAC, 50-60 Hz).VentilationMaximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc. Shipping Weight4.4 lbs. (2.0 kg)
Price: 899.99 USD
Location: Atlanta, Georgia
End Time: 2024-10-03T00:42:33.000Z
Shipping Cost: 15 USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
Brand: Symetrix
Type: Dante/Analog Audio Interface
Features: Dante
MPN: 80-0106
